Differences

This shows you the differences between two versions of the page.

--- documentation:issues [20:06 03.12.2013] – Walter
+++ documentation:issues [14:50 17.08.2021] (current) – Uncollapse Diego Jahn
@@ Line 1: / Line 1: @@
 ===== Known Issues =====
-==== Modeling ====
+==== Installation ====
-++++ ''Function'' gives erroneous values |
+=== Installation on Mac OSX ===
-''Function''s have been reported to generate erroneous values under the following conditions:
+Please see the page on [[download:osx_10.8_users|troubleshooting for Mac]].
-  * ''Function'' is defined outside of ''System'' but used inside ''System'' (which is allowed)
-  * OpenMP multithreading is used (i.e. Settings/Local/Threads per jobs < 1).
-Work around:
+==== Simulation ====
-  * Drag ''Function'' inside the ''System''
-++++
+=== ''Function'' gives erroneous values ===
-==== GUI ====
+''Function''s have been reported to generate erroneous values in the following situation:
+  * ''Function'' is defined outside of ''System'' but used inside ''System'' (which is allowed) and
+  * OpenMP multithreading is used (i.e. Settings/Local/Threads per jobs > 1).
-++++ Added item does not appear (immediately) in Editor (tree view) |
+Work around:
+  * Drag ''Function'' inside the ''System''
-As a workaround, click on the element in the Document view. This will force updating the tree view.
+  * Or, use only single thread per job.
-++++
+==== Visualization ====
-++++ Drag/dropping items in Editor mixes up subitems |
+=== Gnuplot says "unknown or ambiguous terminal type" ===
-As a workaround, click on the element in the Document view. This will force updating the tree view.
-++++
-++++ Some jobs continue despite stopping multiple jobs in ''JobQueue'' |
-If this occurs, you will need to remove the remaining jobs by selecting and removing them again.
-++++
-==== Simulator ====
-++++ Gnuplot says "unknown or ambiguous terminal type" |
 Morpheus depends on [[http://www.gnuplot.info|Gnuplot]] version 4.4. Please update [[http://www.gnuplot.info|Gnuplot]]. \\ \\
@@ Line 42: / Line 27: @@
 In many cases, this error is due to the fact that the ''PDF'' and ''PNG'' terminals depend on ''libcairo''. As a workaround, one can use another terminal such as ''SVG'' or ''JPG''.
-++++
+=== Gnuplotter on-screen output shows flickering ===
-++++ Gnuplotter on-screen output shows flickering |
 Some gnuplot terminals, such as Aquaterm in Mac OSX, are relatively slow and may show flickering when run under ''interactive'' mode.
@@ Line 52: / Line 35: @@
   * In ''local'' mode: Use a file terminal such as ''png'' and ''pdf''.
-++++
 ==== Report an issue ====
-++++ Found a bug? Send us a report. |
+=== Found a bug? Send us a report. ===
 If you experience reproducable crashes in a situation that is not covered here, please send us a [[joern.starruss@tu-dresden.de|bug report]]. \\
@@ Line 67: / Line 49: @@
   - Log file of the debugger (''gdb.log'')
-++++
+==== GUI ====
+=== Added item does not appear in Editor (tree view) ===
+As a workaround, click on the element in the Document view. This will force updating the tree view.
+=== Drag/dropping items in Editor mixes up subitems ===
+As a workaround, click on the element in the Document view. This will force updating the tree view.
+=== Some jobs continue despite stopping multiple jobs in ''JobQueue'' ===
+If this occurs, you will need to remove the remaining jobs by selecting and removing them again.
+=== Simulation state [SnapShot].xml.gz cannot be restored (under Windows) ===
+It has been reported that snapshots of simulation states, in compressed model files (''[SnapShot].xml.gz''), cannot be restored under Windows. This is most likely due to a corruption in file compression.
+A solution or workaround has yet to be found.